Motorsport composite engineering · North America & UK / Europerfq@racecomposites.com

Regulations

Motorsport composite technical regulations

Before material and process, the rulebook. What a series allows in carbon, what it demands of safety structures and what it freezes by homologation decide what can be built at all.

Always read the current text. This page summarises how rules typically affect composite parts. Regulations change every season and differ by series and national sporting authority; the current Appendix J article, series technical regulations and your scrutineer decide. We check the applicable text during DFM review.

FIA Appendix J: bodywork

Appendix J to the FIA International Sporting Code sets the technical rules for production-based and many national categories. For composites, the key points are:

  • Production-based groups. In classes built from road cars, bodywork must usually keep the homologated material unless the homologation form or a variant option lists a composite part. Replacing a steel bonnet with carbon is only legal where the rules or homologation allow it.
  • Free-material classes. Where materials are free, carbon and aramid composites can be used for bodywork, but dimensions, aerodynamic devices and minimum weights still apply.
  • Material restrictions. Some articles restrict exotic fibers and high-modulus materials on specific parts to control cost. Check the article for the group you race in.

Safety laminates and strain-to-failure

Safety structures must fail progressively rather than shatter into sharp splinters. FIA safety rules therefore specify materials with a minimum strain-to-failure, commonly 1.5%, for laminates on parts such as seats, survival cell anti-intrusion skins and crash structures. High-modulus carbon on its own fails at much lower strain; that is why safety laminates mix in aramid, high-strain carbon or other tough fibers.

StructureTypical composite requirementMaterial approach
Survival cell anti-intrusion panelsPenetration resistance on the cockpit sidesAramid (Kevlar) and Zylon (PBO) plies within the carbon skin
Fuel cell housings / crash enclosuresCrush and penetration protection around the cellSandwich construction with aramid skins; FIA-approved bladder inside
Impact attenuators / crash structuresProgressive crush absorbing a specified energy at a limited decelerationTapered carbon or aramid tubes and cones, homologated by test
Seats (FIA 8862 / 8855 standards)Tested and labelled to the standardBought homologated; not built as one-offs
Splinter-sensitive bodyworkParts near drivers and spectators must not shatterCarbon-Kevlar hybrid outer plies
Endurance prototype race car on a banked circuit
Prototype and open-wheel categories combine free aero with tightly specified safety structures.

GT3 Balance of Performance vs time attack

Series typeWhat composites you can changeWhat it means for an RFQ
GT3 / GT4Bodywork and aero fixed by the manufacturer homologation; BoP adjusts ballast, power and some aero settingsReplacement parts must match the homologated geometry; usually from existing molds
Time attackAero largely free within class dimensions; materials freeNew CFD-driven aero, one-offs and iterations
SCCA / NASA club racingClass-dependent: some allow composite bodywork and aero, production classes restrict itCheck the class rules for allowed panels and wing dimensions
HillclimbOften open aero in modified classesDownforce-per-kg packages, quick-change parts

Formula SAE / Formula Student

Formula SAE rules allow composite monocoques and bodywork but require teams to prove equivalence to the baseline steel spaceframe. That means a structural equivalency submission, laminate test panels (typically three-point bend and perimeter shear tests) built with the same layup and process as the chassis, and documented attachment of harness and roll hoops. Impact attenuators are either a standard design or tested. Composite aero is free within dimensional limits.

Building to a specific rulebook? Note the series and article in your RFQ.

Submit RFQ

Related: aero & bodywork, prepreg & core guide, NDT & crash repair.

Submit an engineering RFQ

Send what you have. We return a DFM review and a production plan.

  • CAD or sample STEP / IGES, a 3D scan, or the physical part to reverse-engineer
  • Spec intent process, fiber grade, core and resin Tg (or let us recommend)
  • Quantity one-off, spares set or season batch
  • Race deadline the event or test date the part must make
Submit engineering RFQ

Or email rfq@racecomposites.com. DFM and capacity check within 1–2 business days.