Motorsport composite engineering · North America & UK / Europerfq@racecomposites.com

Process guide

Autoclave prepreg vs OOA prepreg vs VARTM infusion

The cure route sets the fiber volume, the void content, what the tool has to survive and how the cost splits between tooling and every part after it. This is how the three compare on a race part.

Eight dimensions side by side

DimensionVARTM resin infusionOOA prepregAutoclave prepreg
Fiber volume fraction Vf45–55%~53–58%55–65%+
Void content1–3%, operator dependent<1–2% with good debulking<1%
Pressure / temperature~1 bar (vacuum), ambient or oven post-cureVacuum only, oven 80–135 °C typical3–7 bar, 120–180 °C
Storage & out-life scrapDry fabric, infinite shelf life; resin mixed per shotFreezer −18 °C, out-life tracked; expired material scrappedFreezer −18 °C, out-life tracked; expired material scrapped
Tooling CapExLowest: epoxy/glass tools, single-sidedModerate: vacuum-tight, temperature-rated toolsHighest: pressure-rated, CTE-matched carbon or metal, egg-crate backed
Consumable waste per partHigh: flow media, spiral, resin lines, catch potModerate: breather, film, bagModerate: breather, film, bag, sealant
Labor skillInfusion strategy and leak-free baggingPrepreg layup, debulk disciplinePrepreg layup, autoclave scheduling and logging
Break-even guidanceOne-offs and body panels where weight is secondaryWings and panels when autoclave queue or cost is the bottleneckStressed aero, floors, structures, anything where stiffness-to-weight wins races

Why the numbers differ

Consolidation pressure does two things: it squeezes excess resin out (higher Vf) and it collapses trapped air and volatiles (fewer voids). Infusion only has atmospheric pressure to work with, so the laminate carries more resin per ply and is heavier and less stiff for the same fiber. Autoclave prepreg starts with a controlled resin content (typically 38–42% by weight) and adds 3–7 bar on top of vacuum, which is why it is the default for dry carbon race parts.

Out-of-autoclave prepregs are formulated with partially impregnated "breathing" plies that let air escape under vacuum alone. With disciplined debulking they get close to autoclave quality on moderate thicknesses, and they remove the autoclave as a scheduling bottleneck.

Rule of thumb. Every 5 points of Vf is roughly 8–10% of laminate stiffness and a few percent of mass. On a splitter or wing that difference matters; on a dash panel it usually does not.

Decision framework by part class

Part classTypical partsRecommended routeWhy
Non-structural body panelsDash, door cards, side skirts, coversVARTM or OOALow load; tooling cost dominates small batches
Stressed aeroSplitter, undertray, wing elements, diffuserAutoclave (OOA acceptable for club programs)Stiffness-to-weight and fatigue under aero load
Hollow or closed sectionsWing mainplanes, struts, ducts with internal pressureAutoclave or OOA with bladderInternal pressure needs prepreg; infusion cannot consolidate it
Crash and safety structuresSurvival cells, impact attenuators, fuel cell housingsAutoclave only, to the regulationHomologation, traceability and void limits
High-temperature zonesBrake ducts, heat shields, engine bayAutoclave or OOA with high-Tg resinResin Tg must clear heat soak with margin

Compare all three routes on your part and batch size.

Run the process comparison

Batch size changes the answer

At quantity one, tooling is often 70–85% of the program, so the cheaper tool that VARTM allows can halve the bill. By 10–25 parts the recurring cost per part dominates; autoclave prepreg's lower scrap of rework and higher consistency usually make it the better buy, and the tool cost is spread thin. The estimator's process table shows exactly where that crossover lands for your area, geometry and stack.

Close-up of 2x2 twill carbon fiber laminate surface
A 2x2 twill prepreg surface: consistent weave and resin content are what autoclave consolidation buys.

What to put in the RFQ

  • Part class and load: is it cosmetic, aero-loaded, or structural?
  • Heat exposure, so the resin Tg can be chosen (see the prepreg & core guide).
  • Quantity across the season, including spares.
  • Any regulation that fixes the material or process (see motorsport composite regulations).

Submit an engineering RFQ

Send what you have. We return a DFM review and a production plan.

  • CAD or sample STEP / IGES, a 3D scan, or the physical part to reverse-engineer
  • Spec intent process, fiber grade, core and resin Tg (or let us recommend)
  • Quantity one-off, spares set or season batch
  • Race deadline the event or test date the part must make
Submit engineering RFQ

Or email rfq@racecomposites.com. DFM and capacity check within 1–2 business days.