Motorsport composite engineering · North America & UK / Europerfq@racecomposites.com

Aero & bodywork

Race aero & bodywork structures

Splitters, wings and diffusers carry hundreds of kilograms of downforce through a few bolts. Hoods and doors are where the easy kilograms come off. This is what each component saves, costs and needs structurally.

Component by component

ComponentWeight savedClub / wet carbonPro / GT3 dry carbonStructural focus
Front splitter + undertray5–15 lb (2–7 kg)$800 – $2,000$2,500 – $6,000+Stiff in bending under ground-effect load; rod mounts and chassis hardpoints; skid-block wear zone
Rear wing assembly10–25 lb (4–11 kg)$1,200 – $2,500$3,500 – $10,000+Mainplane torsion and bending, endplate and swan-neck mounts, flap gap control
Rear tunnel diffuser5–10 lb (2–4.5 kg)$600 – $1,800$2,000 – $5,000+Strakes and tunnel shape held under load; heat near exhaust
Vented hood / bonnet15–30 lb (7–14 kg) vs steel$1,000 – $2,500$2,500 – $5,000+Latch and hinge inserts; heat soak from radiator exit and turbo
Race doors (pair)40–140 lb (18–63 kg) vs OEM steel$3,000 – $8,000+ per pairSide-impact rules, hinge and latch hardpoints, window mounts
Brake ducts & airboxes0.5–2 kg each$300 – $1,200$800 – $3,000High-Tg resin near rotors and engine; closed sections often bladder-molded
Weight savings against typical OEM or aluminum equivalents; prices are per component for small batches.

Load paths and hardpoints

Most composite aero failures start at a bolt, not in the middle of a panel. A good aero part spreads point loads into the laminate before they reach it:

  • Local build-ups. Extra plies around every hardpoint, ramped at roughly 1:20 so the stiffness change is gradual.
  • Core inserts. In sandwich panels the core is replaced locally with high-density foam, potting compound or a solid laminate block where a bolt passes through, so clamping does not crush the core.
  • Bonded metallic inserts. Titanium (galvanically compatible with carbon) or anodized aluminum bushes and brackets, bonded with toughened structural adhesive in jigs after 5-axis drilling.
  • Isolation. Aluminum in contact with carbon needs a glass ply or barrier to avoid galvanic corrosion.
Touring race car cornering over a red and white kerb
Splitters take kerb strikes as well as downforce; skid blocks and sacrificial leading edges are part of the design.

Panels: sizing the sandwich

Large flat aero surfaces are usually sandwich panels: thin carbon skins over Nomex honeycomb or Rohacell PMI foam. Doubling the core thickness roughly quadruples bending stiffness for a small weight gain, which is why a 10 mm-core splitter with two plies per skin can outperform a 6 mm solid laminate at a third of the mass.

Size your splitter, wing or floor panel against the real span and load.

Open the laminate calculator

GT3 BoP vs time attack philosophy

GT3 / GT4 (homologated)Time attack / open aero
Aero geometryFixed by homologation; adjustments within BoP windowsLargely free within class box dimensions
What you buyExact-spec replacement parts and spares, often from customer moldsNew CFD-driven splitters, wings, diffusers, frequently one-offs
MaterialMatching the homologated spec matters more than the lightest stackLightest stack that holds shape at peak downforce
PriorityRepeatability, fast pit replacement, documented conformityDownforce per kilogram, stiffness, quick iteration

Rules that restrict composites on bodywork are covered in motorsport composite regulations. For damaged aero, see NDT & crash repair.

Submit an engineering RFQ

Send what you have. We return a DFM review and a production plan.

  • CAD or sample STEP / IGES, a 3D scan, or the physical part to reverse-engineer
  • Spec intent process, fiber grade, core and resin Tg (or let us recommend)
  • Quantity one-off, spares set or season batch
  • Race deadline the event or test date the part must make
Submit engineering RFQ

Or email rfq@racecomposites.com. DFM and capacity check within 1–2 business days.